Show Keyboard Shortcuts

Dump Buggy Tipper

BTM/300/2000/B/G

BTM/300/2000/B/G-

Features

  • Stainless Steel or Mild Steel Construction
  • Food/Pharmaceutical Industry Specification
  • Standard and Custom Design Machines
  • Fully TIG/MIG Welded Construction
  • Lifts for Bins, Drums, Trays etc
  • Tip Heights up to Customers’ Requirements
  • Lifting Capacity up to 600Kgs
  • Chain or Screw Drive
  • Fully Enclosed Safety Guard
  • Fully Load Tested and UKCA or CE Certified
  • LOLER Inspection and After Sales Service Available
  • Direct from a British Manufacturer
Description

BTM/300/2000/B/G Single Pillar Dump Buggy Tipper

This Dump Buggy Tipper is designed to lift and tip a standard 400 lbs Dump Buggy at a discharge height of 1600mm. The Dump Buggy Tipper is manufactured from Grade 304 stainless steel, is a welded construction throughout and is designed to be bolted to the floor. The lifting is achieved by a ¾” Simplex chain driven by a motor gearbox mounted at the top of the main column. The Dump Buggy Tipper was tipping waste from a High Care Area into a chute feeding in the Low Care Area. The Waste Chute had a pneumatically operated lid which opened when the Dump Buggy Tipper began to lift with a bin location frame mounted in the Low Care side.

Safety Guard to BS EN 14120:2015 Safety of Machinery Guards

This Dump Buggy Tipper was supplied complete with a safety guard to meet the guidelines of BS EN 14120:2015 Safety of Machinery Guards. The safety guard is constructed from 40 x 40 x 3mm stainless steel box section and 2.0mm stainless steel sheet. It encloses the Dump Buggy Tipper to a height of 2200mm on two sides, 1800mm at the tipping position with a hinged guard door on the fourth side. The guard door is electrically and mechanically interlocked preventing the Dump Buggy Bin Tipper from operating when the door is open. Additionally, the guard door can only be opened when the lift carriage is at the full down position to prevent access whilst a load is raised.

Dump Buggy Tipper Electrical Control

This Dump Buggy Tipper is fitted with an IP65 Stainless Steel Control Panel which is mounted on the main column at a convenient position to give good maintenance access under the Provision and Use of Work Equipment Regulation 1998 (PUWER). Upper and Lower end of travel limit switches are positioned to prevent inadvertent adjustment or damage but are easily adjustable by trained personnel for fine adjustment on site.

The control panel incorporates the following controls; Up, Down, Guard Release, Emergency Stop and a Reset Facility. Once an operator has loaded a Dump Buggy into the tipper and closed the guard door the Start button can be pressed. The Dump Buggy Tipper will begin to lift and in doing so will release a pneumatic limit switch that operates a pneumatic cylinder to open the chute lid. The Dump Buggy Tipper will then proceed to full tip and return to the floor automatically. When it gets back to the floor, it will remake the limit switch and close the chute lid thereby maintaining the integrity of the High Care area. The control panel has a volt free pair of contacts which can be used to connect a ‘Call to Run’ signal if required.

Specification
Description Dump Buggy Tipper
Model No. BTM/300/2000/B/G
Capacity 300 Kgs
Tip Height 2000mm
Tip Angle 135 Degrees
Overall Height 2850mm
Machine Handing Left Hand
Maximum Headroom 4000mm
Tipping Chute Separate Waste Transfer Chute
Container Description 400 lbs Dump Buggy
Base Arrangement Bolted To The Floor
Control Circuit 24Vac
Electrical Rating IP65
Limit Switches Telemecanique
Motor Detail 0.75kW, 480V, 3 PHASE, 60 CYCLE, c/w BRAKE
Gearbox Detail SEW Eurodrive
Output R.P.M 28 R.P.M.
Ratio 50:1
Load/Tension Chain ¾” Simplex
Tensile Strength 3000 Kgs
Lift Speed 6.4 Meters/Minute
Application Story

You May Also Be interested In...

Customer image
300 Litre Bin Tipper
BTM/350/2850/B/G
Customer image
Tote Bin Hoist
BTM/300/2400/B/G
Customer image
Single Pillar Hoist
BTM/300/3800/B/G
Customer image
Single Pillar Lifter
BTM/350/2635/B/G
Customer image
Tray Tipper
BTM/350/1600/M/G
Customer image
Column Lifter Guarded
BTM/250/3700/B/G
Customer image
Guarded Trolley Tipper
BTM/250/2200/B/G/SL
Customer image
ATEX Bin Tipper
BTM/300/2500/M
Customer image
Guarded Drum Tipper
BTM/300/1900/B/G/140
Customer image
Guarded Bin Tipper
BTM/300/4450/B/G
Customer image
Guarded Dump Buggie Tipper
BTM/300/1854/M/G
Customer image
High Level Bin Tipper
BTM/350/4650/B/G
Customer image
Salad Bin Tipper
BTM/250/1200/B/G
Customer image
Tote Dumper High Level
BTM/100/5850/B/G
Customer image
Stillage Tipper
BTM/400/1850/B/G
Customer image
Guarded Tote Bin Tipper
BTM/300/1600/B/G
Customer image
200 Litre Tote Bin Tipper
BTM/300/2400/B/G-
Customer image
Dump Buggy Tipper
BTM/300/2000/B/G-
Customer image
Dough Tipper
BTM/300/3000/M/G